Svoemesto Kayfun [Lite] XS Centre pin 

The XS centre post is an optional performance accessory for the Kayfun [Lite] 2019 atomiser.

Designed for optimisation of setups that require an extremely tight draw.
Maximum Airflow: 1.2mm

Contains 2 AFC grub screws. 

Note: This item is NOT compatible with the Kayfun [Lite] Plus

Eleaf ELLO HW Series heads - 5pk

Pack of 5 x replacement heads for the following tanks and kits:

Eleaf ELLO tank
iStick Pico 25 and ELLO tank kit by Eleaf
Invoke and ELLO T kit by Eleaf

Choice of coils:
HW1 - Single stainless - 0.2Ω (40-80W)
HW2 - Dual kanthal - 0.3Ω (30-70W)
HW3& - Triple kanthal - 0.2Ω (50-130W)
HW4 - Quad kanthal - 0.3Ω (40-110W)
HW-M - Multihole kanthal - 0.15Ω (70-80W)
HW-N - Net kanthal - 0.2Ω (65-750W)

Important
Atomiser heads are disposable consumable parts and as such, are covered by our DOA warranty only. See our Terms & Conditions for more information.
These are sub-ohm heads and you must make sure the battery/device you are using is fully capable of safely supporting the required drain rate. We strongly recommend you thoroughly research the topic before embarking on any experiments with sub-ohming. We will not accept any responsibility for any damage caused by sub-ohming activity.

Wire rods by Crème de Vape

12cm lengths of twisted wire in a handy tube. These specialised wires should take your rebuildable atomiser to the next level.
Specialist wires can be ruined when wound up on a reel, so we've sourced these rods so that the fancy twisting is preserved right up till you come to make your coil.

Choose from the following types:

• Tiger wire - Nh32g*1.2+K24g - 10pcs
• Ni200 Clapton Wire - Ni32g+Ni26g - 30pcs
• Fused Clapton Wire - K32g + K26g*2 - 30pcs

Standard Silica Wick - 5m 

Approximately 5 metre length of Standard Silica Wick for rebuildable atomiser coils.
Available in two widths.

Nickel (Ni200) Wire - 10m

10 metre reel of Ni200 Nickel wire for building coils strictly for use on a device that supports temperature sensing mode.

Available in  0.3mm and 0.4mm 

Nichrome Resistance Wire 

Wire for rebuildable atomiser coils.

Nichrome 0.15mm / 35ga
Nichrome 0.16mm / 34ga
Nichrome 0.20mm / 32ga

UD Ferris Wheel V1 Pack of Speciality pre-built coils

Handy Ferris Wheel shaped pack containing 70 pre-built Kanthal A1 speciality coils as follows:

• 24AGW (0.5mm),0.5Ω * 10pcs
• 26AGW (0.4mm),1.2Ω * 10pcs
• 26AGW (0.4mm),1.0Ω * 10pcs
• 30AGW*4 quad-twisted,0.5Ω * 10pcs
• 28AGW*2 double twisted,0.5Ω *10pcs
• 26AGW*2 double twisted,0.5Ω *10pcs
• 26 AGW+32 AGW clapton coil ,0.6Ω *10pcs

Pack of 10 Speciality pre-built coils

Pack of 10 pre-built speciality coils for super-easy RBA building.

These coils are perfectly suited for drippers and tanks with large wire holes, and wide-open airflow.

Choose from the following:

• SS316L Staggered Fuse Clapton Coils - 26GA(0.4mm)+32GA(0.2mm)*2+(0.5*0.1) *ID2.5- resistance 0.2Ω
• A1 Kanthal Alien Coils - 26GA(0.4mm)*3+32GA(0.2mm)*ID2.5 - resistance 0.15Ω
• Ni80 Fused clapton Coils - 30ga*2+40ga ID2.5 - resistance 0.80Ω
• Ni80 Fused clapton Coils - 26ga*2+36ga ID3.0 - resistance 0.30Ω
• Ni80 Tricore fused clapton Coils - 3-28ga+36ga ID2.5 - resistance 0.32Ω
• Ni80 MTL staple clapton Coils - 4-0.1*0.3/40ga ID2.5 - resistance 0.68Ω
• Ni80 MTL staple clapton Coils - 8-0.1*0.3/36ga ID3.0 - resistance 0.34Ω
• Ni80 MTL staple clapton Coils - 2-28ga/4-0.1*0.3/36ga ID3.0 - resistance 0.30Ω
• Ni80 Alien Coils - 3*28ga/36ga ID3.0 - resistance 0.36Ω
• Ni80 Alien Coils - 3*26ga/36ga ID3.0 - resistance 0.21Ω

Pack of 10 Speciality pre-built coils

Pack of 10 pre-built speciality coils for super-easy RBA building.

These coils are perfectly suited for drippers and tanks with large wire holes, and wide-open airflow.

Choose from the following:

• SS316L Staggered Fuse Clapton Coils - 26GA(0.4mm)+32GA(0.2mm)*2+(0.5*0.1) *ID2.5- resistance 0.2Ω
• A1 Kanthal Alien Coils - 26GA(0.4mm)*3+32GA(0.2mm)*ID2.5 - resistance 0.15Ω
• Ni80 Fused clapton Coils - 30ga*2+40ga ID2.5 - resistance 0.80Ω
• Ni80 Fused clapton Coils - 26ga*2+36ga ID3.0 - resistance 0.30Ω
• Ni80 Tricore fused clapton Coils - 3-28ga+36ga ID2.5 - resistance 0.32Ω
• Ni80 MTL staple clapton Coils - 4-0.1*0.3/40ga ID2.5 - resistance 0.68Ω
• Ni80 MTL staple clapton Coils - 8-0.1*0.3/36ga ID3.0 - resistance 0.34Ω
• Ni80 MTL staple clapton Coils - 2-28ga/4-0.1*0.3/36ga ID3.0 - resistance 0.30Ω
• Ni80 Alien Coils - 3*28ga/36ga ID3.0 - resistance 0.36Ω
• Ni80 Alien Coils - 3*26ga/36ga ID3.0 - resistance 0.21Ω

Ni80 Nichrome Resistance Wire

Nichrome wire for rebuildable atomiser coils. Ni80 wire is excellent for single or dual coil builds in both RDA and RTA atomisers, it's easy to work with and holds up very well for a wide range of applications. Great for use in the Kayfun and SQuape series. Not suitable for temperature control applications.

• 32ga - 30ft
• 28ga - 30ft
• 26ga - 30ft
• 24ga - 30ft
• 22ga - 15ft

Please note: Packaging is subject to change and may vary slightly from that in photos.

Ni80 Nichrome Resistance Wire

Nichrome wire for rebuildable atomiser coils. Ni80 wire is excellent for single or dual coil builds in both RDA and RTA atomisers, it's easy to work with and holds up very well for a wide range of applications. Great for use in the Kayfun and SQuape series. Not suitable for temperature control applications.

• 32ga - 30ft
• 28ga - 30ft
• 26ga - 30ft
• 24ga - 30ft
• 22ga - 15ft

Please note: Packaging is subject to change and may vary slightly from that in photos.